| TJ Gas Tank Skid Plate *Rubicon Ready!*
 Our
Gas Tank Skid Plate offers excellent protection for the Jeep TJ. This skid was built
from 3/16" steel plate in 3 pieces that were laser cut, formed and welded together.
It utilizes the stock mounting locations to keep the installation time to a minimum.
You will not use the stock tin shield as part of this skid.
Our TJ skid has been moved to the passenger side by 3/4" to allow for
more shock clearance on the driver side and it raises the tank up another 1" for increased
clearance over stock setups and even more vs. other skids that go over the stock shield.
The rear of the skid has a departure angle built in to aid in sliding over obstacles.
The front has a new design allowing 3/4" more differential clearance over the previous
design. Four drain holes are incorporated into the design and the factory straps are
used to secure the tank to the skid. More material has been removed from the front of
the skid to give the track bar more room to cycle.
This skid will fit 1997-2002 TJ's without a body lift with slight modification
to the tank straps. 2003 Wranglers will require a 1" body lift due to the new changes.
At 60 lbs each, this skid is no lightweight!
|
 |
YJ Gas Tank Skid Plate
 Built
similar to our TJ skid, our YJ skid also uses laser cut 3/16" steel which is formed
and welded for complete protection against the elements. This skid does not cover the
stock skid, it replaces it. Four drain holes are incorporated into the design and the
factory straps are used to secure the tank to the skid. Because of the cross member
that sits above the front of the gas tank, this skid cannot be raised to gain more ground
clearance. The skid was designed to offer the maximum allowable side and differential
clearance.
|
|
CJ Gas Tank Skid Plate
 Laser
cut, formed and welded together for excellent accuracy and great looks. Our CJ skid
is cut from 3/16" steel and offers excellent protection against the elements. Four drain
holes are incorporated into the design and the factory straps are used to secure the
tank to the skid. This skid fits the stock 20 gallon plastic tank only. Because of the
cross member that sits above the front of the gas tank, this skid cannot be raised to
gain more ground clearance. The skid was designed to offer the maximum allowable side
and differential clearance. The drivers side was left tall to deflect heat from the
exhaust.
|
|
| Large Inside Rack
Kilby Enterprises has designed and developed a rack specifically
for the Jeep TJ. The Kilby rack mounts inside the Jeep to give you two layers
of storage space for those long weekend trips. The installation is quick and easy,
allowing you to re-install the rear seat when you need it.
- Measures 48" wide, 32.5" deep and 4" tall
- Constructed of 1" square tubing and expanded metal
- All joints are fully TIG welded on the outside and MIG welded
on the inside
- It can be used with both the hard top or soft top without
interfering with the soft top bows
- No drilling is required. We use two factory bolts on the sports
bar and four factory holes in the rear
- Sits 17" off the floor giving you plenty of storage space
below
- Powder coated in a Satin Black and use over sized hardware.
Why? Because it's simply the best on the market!
- Includes everything needed to install quickly and easily
|
|
|
|
| "Sport" Inside Rack
In addition to our larger KE-TJR1 rack, we have designed a rack
specifically for the Jeep owner that would like to keep their Tuffy or Con-Ferr
rear storage box. This rack also mounts inside the Jeep but utilizes a different
rear mounting method. Again, the installation is quick and easy, allowing you
to re-install the rear seat when you need it.
- Measures are 48" wide, 21" deep and 4" tall
- Constructed of 1" square tubing and expanded metal
- All joints are fully TIG welded on the outside and MIG welded
on the inside
- It can be used with both the hard top or soft top without
interfering with the soft top bows
- No drilling is required. We use two factory bolts on the sports
bar for the front mounts and the two seat belt bolts located near the floor
for the rear mounts
- Sits 17" off the floor giving you plenty of storage space
below and enough space for your rear storage box
- Powder coated in a Satin Black and use over sized hardware.
Why? Because it's simply the best on the market!
- Custom made to each order only
- Includes everything needed to install quickly and easily
|
|
|
|
Deep Transmission Pans
Mopar Performance extra-capacity steel pan improves cooling
and lubrication of critical transmission components. Results in better shift performance
and longer component life. Spacer provided to lower the fluid pickup. Cures the unwanted
tranny wash out problems found in TJ's when ascending steep hill climbs. Includes drain
plug, filter and hardware needed for a complete installation.
|
|
Mil-Spec Toggle Switches & Covers
 These
switches & covers are the ultimate! Used around the world in many military and commercial
aircraft. Switches are dust and moisture proof and do not require a rubber boot to seal
out the elements.
- High strength, temperature & enviroment resistant, non-tracking
case material
- Silver cadmium oxide contacts
- Silver plated terminals
Only the best! We carry Kilby two models in stock and can
supply other models as well. If you have a specific need and don't see what you need
here, contact us for a quote.
* Please note that not all covers are the same. These covers are designed to turn the
switch off when in the closed position. If you use the MS25224-1 cover on the
MS24523-27 switch, you will actually turn the switch on when the cover is closed. Please
be sure of your switch type when ordering.
* Color of switch may vary depending on actual build date
MS24523-22 This is a standard ON/OFF SPST toggle
with silver plated terminals for the best continuity and has a 15A rating. Use it for
lights, compressors or winch master switch when wiring the winch inside the vehicle.
Use cover P/N MS25224-1 with this switch.
|
|
 MS24523-27
This is a Momentary-ON/ OFF / Momentary-ON SPDT toggle switch. It has the same features
of the -22 toggle above but is used "momentarily" to turn accessories on and has a 10A
rating. Many four wheelers use this switch to control the winch direction from inside
the cab. Use cover P/N MS25225-3 with this switch
|
|
TJ Switch Centers
 The
Switch Center was designed to provide a clean functional space for mounting gauges and
switches in your Jeep TJ. It's made of durable ABS and comes blank to allow you to add
your own accessories as you see fit. Installation is a snap using 2 factory screws.
Drilling two holes in plastic is required. Max measurements at the base is: 9.5" Wide
x 4" Deep and stands 3.75" tall at highest point. Useable mounting area is 8.25" Wide
x 3" tall. The bottom is left completely open for running wires etc.
|
|
Mil-Spec Battery Terminals
 Kilby
Battery Terminal Adapters are used for mounting electrical leads to battery terminals
on industrial lift trucks, tractor trucks, off road vehicles and many military applications
for the US Army, Navy, Marines, and Coast Guard. The basic shape style is for A26 battery
posts. Mil spec battery terminals featuring a thick lead body and 3/8 bolt to attach
any accessory needed. Both bolts are reversible to allow for an easier installation.
|
|
